> LED lighting > LED drivers and power supplies > LED driver multifunctional

LED driver multifunctional

LED junction boxes can be found here.

Prices are exclusive of VAT.

LED driver multifunctional

Filters

Filter on:

? Either show items that are in stock or items that are not in stock.

? A conventional ballast has a wound coil. It is somewhat cheaper to buy, but more expensive to run because more power is converted into heat. An electronic ballast not only has a lower power consumption, but it also has the advantage of longer lamp life.

?

Version of the ballast.

? If the product is unbranded, we do not have a regular supplier for it. Therefore, the product version may slightly vary.

? Connecting cable length in metres.

? Most common colour in the product.

? Articles classified by component type.

? Connection type of the output.

?

The way the power can be connected.

? The way the power can be tapped for looping through.

? Diameter in millimetres, measured at the widest point.

? Dim type: AM, PWM or hybrid.

? Some lamps and ballasts are dimmable. There are different types of dimmers and different ways to dim a ballast or transformer. In case of insufficient knowledge, please check with our sales department.

? Not every dimmable ballast or light source can dim to 0% level, here is the dimming range.

? Maximum height in millimetres.

?

This may be a fixed voltage or two values with a hyphen.
You can use the product within these limits.

?

The IP (Ingress Protection) code indicates the degree of protection against ingress of moisture and solid objects. The code consists of two firures.
The first figure indicates the protection against objects and dust:
IP 0x - not protected
IP 1x - protected against objects with a diameter above 50 mm
IP 2x - protected from objects with a diameter greater than 12 mm (touch safe)
IP 3x - protected from objects with a diameter greater than 2.5 mm
IP 4x - protected against objects with a diameter greater than 1 mm
IP 5x - protected against dust ( dust )
IP 6x - dustproof

The second figure indicats the protection against water:
IP x0 - unprotected (plain)
IP x1 - Protected against dripping water (drip)
IP x2 - Protected against dripping water when tilted to 15 degrees
IP x3 - protected against spraying water (rain tight)
IP x4 - protected against splashing water (splash proof)
IP x5 - protected against water jets (splashproof)
IP x6 - protected from rainstorms
IP x7 - protected against accidental immersion (30 minutes to 1 meter deep) (waterproof)
IP x8 - protected from stay under water (pressure proof)

? Luminaire including or excluding lamp(s).

? Product length in millimetres. For fluorescent tubes, this excludes the metal pins on the end unless otherwise stated.

? Material of which the major part of the product is made.

? Maximum amount of power, expressed in watts, that can be connected to the transformer in order to work properly. If the assets exceed this maximum amount, the transformer may behave abnormally: known phenomena in electronic transformers are the lights switching on and off, and no output voltage.

? The minimum power must be connected to the transformer to work properly. If the assets are below the transformer behave abnormally. Known phenomena are electronic transformers are flashing lights, brighter and fainter burning lamps and no output voltage.

A conventional wound transformer must be at least 75% of the maximum power charge. If the load is below this limit, the output voltage too high making the lamps extremely much shorter life. The color of the lamps is usually very white.

? Each type of LED requires a different driver. Current-controlled LEDs of 350, 700, 1050 and 1400mA need to be connected in series. This can be easily done with an LED distributor. Unused outputs are shorted with a wire . First connect the wires, then you can put power on! Never disconnect wires under power!

? The output voltage is indicated here. Voltage-controlled LEDs must always be connected in parallel.

? Outside Dimension is the largest size, often of the lamp head.

? Product shape.

? This may be either a fixed voltage or two values, in which case the product can be used within these limits.

? Maximum width in millimetres.

Height

>

>

? Maximum height in millimetres.

Width

>

>

? Maximum width in millimetres.

Show all filters

Show less filters

206 products 5 6 7 8 9 10 11

TCI 126046 OF LV HR Track 2L 1-10V 357 OF 350-700mA LED driver voor 48V DC print zonder behuizing

29101064 :: show details

TCI 126046 OF LV HR Track 2L 1-10V 357 OF 350-700mA LED driver voor 48V DC print zonder behuizing dmv dipswitch intern instelbaar voor verschillende stromen. LED stroomsturing 350mA 1,1-13W, 500mA 1,5-20W, 550mA 1,7-22W, 700mA 2,1-28W Geschikt voor Stucchi serie 9500 48V rail adaptor, 2 uitgangen voor 2 LED's

Expected 10-05-2026

SLV 1006120 LEDdriver 700mA, 900mA, 1000mA 40W niet dimbaar

29130047 :: show details

SLV 1006120 LEDdriver 700mA, 900mA, 1000mA 40W niet dimbaar

Expected 30-04-2026

SLV 1007227 LEDdriver 350mA, 500mA 20W dimbaar

29130028 :: show details

SLV 1007227 LEDdriver 350mA, 500mA 20W dimbaar

Expected 30-04-2026

SLV 1007229 LEDdriver 150-700mA 25W Dali

29130031 :: show details

SLV 1007229 LEDdriver 150-700mA 25W Dali dmv dipswitch intern instelbaar voor verschillende stromen. LED stroomsturing 150mA 0,3-7,5W, 200mA 0,4-10W, 260mA 0,52-13W, 300mA 0,6-15W, 350mA 0,7-17,5W, 500mA 1-25W, 600mA 1,2-25W, 700mA 1,5-25W

Expected 30-04-2026

SLV 1002082 SLV Valeto LEDdriver Zigbee 350mA, 500mA of 700mA 15W dimbaar

29105358 :: show details

SLV 1002082 SLV Valeto LEDdriver Zigbee 350mA, 500mA of 700mA 15W dimbaar

Expected 30-04-2026

SLV 1004781 LEDdriver 500mA, 600mA en 700mA 21-29,5W niet dimbaar

29130021 :: show details

SLV 1004781 LEDdriver 500mA, 600mA en 700mA 21-29,5W niet dimbaar

Expected 30-04-2026

Prices ex. shipping & handling

You've viewed 206 of 206 items

206 products 5 6 7 8 9 10 11

© 2026 First Light B.V.